TAKATA | HARDWARES

Regular price $ 14.95

Special hardware for use with Takata Harnesses will help you secure your harness to the vehicle in the best way possible for your specific application.
BENDABLE SNAP ON KIT
This kit is to be used in conjunction with the Snap-On end fittings on Takata Harnesses. Use this bracket to bolt into a hard to reach place in your car, then snap the harness on to it.
Brackets are designed to be bent up to 90° in either direction. Do not bend back and forth repeatedly, as this will weaken the metal and could result in unsafe conditions.
Part #: tr 01324kit
3 BAR SLIDE (LV10)
Standard 3 Bar Slide for 2" webbing. Uses the simple 3 Bar Slide wrapping technique. Most commonly used for HANS specific shoulder belts or anti-sub straps.
If you are running in an SFI 16.5 series, you need the LV11NC.
Part #: sr LV10.A
3 BAR SLIDE (LV7)
This 3 Bar Slide is designed to be used to wrap any 3" webbing to a harness bar, or to wrap any end fitting into a 3" piece of webbing. This is the bracket found on all 3" shoulder belts.
Uses the simple 3 Bar Wrapping technique. If you are in an SFI 16.5 series, be sure to select the LV7NC option.
Part #: sr LV7
BOLT IN BRACKET (B23C)

The B23C shares design with the B23B. Its main feature is that it is designed to be bent 90° in any direction while still retaining its strength. Dimensions are 3mm thick (uncoated) and 4mm thick (coated) - 61x81mm with a 13mm (1/2") hole. It can be sewn in, or wrapped with an LV7. 3" webbing must be folded at the edges for use with this bracket. FIA and SFI 16.1 approved.
Part #: sr B23C
BOLT IN BRACKET (B24)
The B24 is the most economical bolt-in bracket offered. It is a heavy-duty Steel bracket that cannot be bent to aid installation. Dimensions are 5mm thick, 69x46mm with a 13mm (1/2") bolt hole. There is a slight 10° bend so that this bracket can be bolted directly to a fl at surface and leave room for webbing wrapped into it. It can be sewn in, or wrapped with an LV4 (recommended), LV10 or LV11. FIA and SFI 16.1/16.5 approved. Cannot be used for a Lap Belt bolt-in bracket under SFI 16.5. 3" webbing must be folded at the edges for use with this bracket.
Part #: sr B24.15.13 NC
BOLTS
Fairly straight forward, these are offered in the lengths shown.
7/16" bolts fit many factory seat belt locations, including European and Asian automobiles.

sr SG10 7/16 25mm
sr SG11 7/16 25mm with Shoulder
sr SG29 7/16 38mm
sr SG57 M8 25mm
EYE BOLTS
These Eye bolts are designed to work perfectly with the B14 Snap On Brackets. Offered in lengths and thread pitches shown.
PART THREAD SIZE THREAD LENGTH
sr SG22 7/16 38mm
sr SG23 7/16 22mm

WAVY WASHER

Whenever a bolt or eye-bolt is used to attach a harness to your vehicle, you should use these wavy washers. One on each side of the sheet metal. They will help keep the bolt from backing out. These are not needed when using the machined sleeve/washer setup for pivoting bolt-in brackets.

We do also recommend using some form of thread locker.

Part #: sr S3

REINFORCEMENT PLATES

Reinforcing a harness mout point is essential when the location has not been engineered by the auto manufacturer. Any time you mount a harness to sheet metal, you will need to put a reinforcement plate under it to keep it from ripping out of the floor.

Available in 3 different thread pitch/sizes.

PART PITCH/SIZE
sr SG39 Standard
sr SG54 M8
sr SG55 M10

 

PLEASE CONTACT US FOR STOCK CHECK AND INQUIRY BEFORE ANY PURCHASE!